The thimble clevis is mainly for ADSS light span tension set which made of galvanized ductile iron.All dielectric dead-ends require a proper size and strength thimble clevis or extension link.Technical characteristics:Model No.: TC-02Associated Bolt size: M14Tension strength: 20KNFinish: hot dip galvanized steelCotter pin: stainless steelDrawing: Installation image(part 2):
Contacta ahora
Galvanized steel thimble clevis is compatible with dead end application to attach loop type dead end to tongue or eye type fittings. It is usually ductile iron material, hot dip galvanized and with 5/8” dia clevis pin.
Contacta ahora
Helical tension set ADSS long span with D shackle, Thimble clevis, helical dead end, protector rods. A dead-end is installed at each end of the cable length to attach to the structures. Two dead ends are used at angle changes of 30 degree or greater, either horizontal or vertical.
Contacta ahora
Product advantages: 1. There is a large contact area between the clamp and the pull wire, the stress distribution is even, there is no stress concentration point, and the achievable grip strength is not less than 95% of the stranded wire Calculate the breaking force. 2. The dead end preformed guy grip is made of the same material as the pull wire, which has good corrosion resistance. 3. The dead end preformed guy grip is simple to install, without any special tools, and can be done independently by one person.
Contacta ahora
There are many types of products with complete models.Hot-dip galvanized bolts, has strong corrosion resistance.Complying International standard, ensure quality.Model No.: P-7Tension strength: 70KNThe main dimensions of the Parallel hanging clevis meets the requirements of the following figure and table:The meanings of letters and numbers in the models in the table are: number--nominal failure load mark.
Contacta ahora
PD extension clevis are mostly made of medium-thick steel by stamping and cutting processes.There are two mounting holes at both ends, hot dip galvanization with strong corrosion resistance.
Contacta ahora
ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
Contacta ahora
The socket clevis W-7A is the connection fitting in the power fittings. In the transmission line, the Wantou Hanging Board W-7A plays the role of suspending the insulator string and the suspension clamp, and bears greater working stress. Its safety performance is very important to the transmission line. The Wantou Hanging Board is in the construction of the power grid.
Contacta ahora
Dead end clamp is made of plastic body with very high mechanical and climatic resistance. A stainless steel flexible cord equipped with movable insulating saddle and two sleeves compressed on the ends to prevent detachment from the clamp body.An inner sheath consisting of two insulating plastic wedges for clamping of the neutral carrier without damaging the cable insulation.
Contacta ahora
Galvanized steel thimble rope is compatible with tension set thickness 2.5mm and hot dip galvanized.
Contacta ahora
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
Contacta ahora
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
Contacta ahora
The TC insert ring is made of Magang, which has high strength and toughness, high vibration damping and good elongation. Malleable iron generally refers to malleable cast iron, cast iron with a certain chemical composition into a white blank, and then annealed cast iron, which has higher strength, plasticity and impact toughness, and can partially replace carbon steel. Technical characteristics:Model No.: TC-05Bolt size: M14Tension strength: 50KN
Contacta ahora
The thimble is made of carbon steel Q235B, and the surface is hot-dip galvanized, smooth and flat, without any defects such as missing plating, zinc particles, bubbles, and cracks. The galvanized layer has sufficient adhesion strength during normal application.
Contacta ahora
Preformed helical guy grip clamp with long span helical dead end, thimble clevis, U shackle, link fitting and pole attachment with related accessories.
Contacta ahora
The adaptor socket clevis W-7B is mainly used to connect the suspension clamp and the insulator string, and cooperate with other accessories to connect the wires and insulate. ALL WELL W-7B has high mechanical strength, is not easy to produce cracks, has good structural stability, the product is not easy to age, and the surface is polished and polished without burrs. In the transmission line, the bowl head hanging board W-7B plays the role of hanging the insulator string and the suspension clamp, and bears greater working stress.
Contacta ahora
Dimensions:Height: 355±5mm.Min. Dry Aring Distance:200mm.Min. Creepage Distance:460mmDiameter Of The Rod:Φ17mm.Coupling Dimensions: Clevis/Tongue.Number Of Sheds:4. Raw Materials:1. End-Fitting:1.1Material: Socket: Cast Iron Or Cast Steel, Hot Dip Galvanized. Ball: Forged Steel, Hot Dip Galvanized.1.2 Minimum Thickness Of The Galvanization:86um.2. Core:2.1 Material: Epoxy& Glass Fiber, Acid-Resistant Type.2.2 Diamter:Φ17mm.3.
Contacta ahora
Light short span tension set for ADSS cable diameter 11.0-12.0mm, tension strength 4KN, and max span 120 meters.The tension dead end guy grip is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction.1.The short span ADSS tension set is used for the installation of ADSS cable, includes ADSS guy grip, Galvanized thimble clevis and U shackle. 2. The structure of the short span ADSS guy grip is simple.
Contacta ahora
The construction process is simplified, the materials are easy to carry, and the installation does not require other auxiliary tools. The construction personnel can operate independently after one teaching, and the appearance after installation is smooth and beautiful. Reduce labor intensity and increase labor productivity.
Contacta ahora
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
Contacta ahora
The middle span ADSS tension set clamp composed of HDG U shackle, galvanized thimble clevis, Chain extension, outer rods and protector rods & inner rods.
Contacta ahora
Preformed inner protection line rods:The material is aluminum-clad steel wire, which is the same material as all the aluminum-clad steel wires of OPPC cable. The inner wall of the protector rods is glued with a layer of gold steel sand through a high-strength polymer water-soluble environmentally friendly adhesive to increase the friction with the optical cable. The rods is preformed into four sub-bundles during production, which is convenient for quick installation.
Contacta ahora
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
Contacta ahora
The stay rods is for 40kN LV stays, the diameter of rods is M16, each element/material stay rod, stay base plate, guy grip, top make off, thimble are easy for assembly.A drawing of stay bows complete with thimble:
Contacta ahora