The self-supporting fiber optic cable clamp ADSS fiber optic cable tension clamp produced by our company, the specification is 5-8mm, is widely used in various optical fiber communication and network projects. Stainless steel wire rope and PA66 main material, injection molding process, color is black. It has the advantages of convenient use, firm fixation, and reduced working hours.
Contacta ahora
Suspension clamps for optical cables are made of real materials, with stable performance and long service life. Composed of insulating clamps and connecting buckles, the stress distribution is even, there is no concentrated point, it can enhance the rigidity of the cable installation point, and the protection performance of the optical cable is good. It has a larger contact area with the optical cable and is equipped with flexible rubber clamps to enhance self-damping and reduce wear.
Contacta ahora
ADSS optical cable suspension clamps are used for the suspension and support of optical cables on straight poles.
Contacta ahora
Tangent suspension clamp for FOR FIBER OPTIC CABLE ADSS Span 120m Diameter of ADSS cable: 11.8 ± 0.4 mm. It is mainly used for the installation of optical cables on short-span linear pole towers below 150 meters, or pole towers with a rotation angle of less than 15 degrees.This product has rubber clamps and one-piece aluminum alloy casing (butterfly type).
Contacta ahora
ADSS optical cable rubber rod down-lead clamp is made of corrosion-resistant, weather-resistant EPDM rubber. It is used for fixing ADSS on the pole tower, suitable for different cable diameters, convenient and reliable installation, and wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table:
Contacta ahora
Fiber optic tangent used as cable suspension hardware best at the same time as the attitude of change, each horizontal or vertical, is a good deal less then 15°.Armor grip suspesnion used for any span duration with an perspective alternate, both horizontal or vertical, a whole lot less than 30°.There are 3 types of ADSS fitting suspension grips: 1. ADSS fitting for span length less than 70msuspension with suspention rods and protection rods, ring type thimble and pole attachment, steel tip, D shackle with related accessories. 2.
Contacta ahora
Fiber optic tangent used as cable suspension hardware first-rate at the identical time because the attitude of alternate, each horizontal or vertical, is a good deal much less then 15°.Armor grip suspesnion used for any span duration with an perspective change, each horizontal or vertical, a whole lot much less than 30°.There are 3 types of ADSS fitting suspension grips: 1. ADSS fitting for span length less than 70msuspension with suspention rods and protection rods, ring type thimble and pole attachment, steel tip, D shackle with related accessories. 2.
Contacta ahora
ADSS Suspension Clamps Depending on the application and the fiber optic cable brand, we provide three types of suspension clamps: low tension, medium tension and high tension. Suspension clamps are mainly used on straight iron towers. They are the connection fittings for hanging ADSS optical cables on the towers. They are used to protect the optical cables from damage during erection and operation. The main technical parameters are the breaking force of the clamp (kN) and the cable.
Contacta ahora
ADSS optical cable small pitch suspension clamps are mainly used for cable erection within 100m pitch, and single-layer pre-twisted wire suspension clamps are mainly used for optical cable erection within 100m~200m pitch.
Contacta ahora
Suspension set for ADSS features: 1.This product has uniform stress distribution and no stress concentration points, which can enhance the 2. Rigidity of the cable installation point without additional damage to the optical cable; The tangent clamp has a high dynamic stress bearing capacity, which can effectively lift and fix the line; 3.
Contacta ahora
Features: 1. It has all the functions of a single suspension clamp.2.
Contacta ahora
Fiber optic tangent used as cable suspension hardware simplest while the attitude of change, ether horizontal or vertical, is less than 15°.Armor grip suspesnion used for any span length with an angle change, either horizontal or vertical, less than 30°. Adss optical cable small pitch suspension clamps are especially used for cable erection within 100m pitch, and single-layer pre-twisted cord suspension clamps are specially used for optical cable erection inside 100m~200m pitch.
Contacta ahora
ADSS optical cable suspension clamps are divided into several types according to the size of the line span, such as single-layer pre-twisted wire tangent clamps, single suspension clamps and double suspension clamps. The tangent clamp for ADSS optical cable is mainly used for the cable erection of 100m span, and the single-layer pre-twisted wire suspension clamp is mainly used for the erection of optical cable within the span of 100m-200m.Features: a. The suspension clamp has a larger contact area with the ADSS/OPGW optical cable, the stress is evenly distributed, and there is n
Contacta ahora
Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.
Contacta ahora
Function: the anti-vibration part dampen wind vibration, consume or weaken the vibration energy generated by the laminar wind during the operation of the optical cable, and prevent the damage of the hardware and the optical cable. Purpose: Suitable for ADSS optical cable. Factors that cause vibration: wind force, wind speed, tension, span, wind direction, topography, landform, fiber optic cable structure, length, etc. Note: The installation position of the spiral damper on the tension clamp or the suspension clamp is the same.Specification required for different cable diameter r
Contacta ahora
FTTH fiber-in-the-home clamp, designed for hanging, flat optical cable. The clamp is very easy to install and does not require other tools. It can be easily installed on the hanging bracket by manually adjusting the hanging ring. The clamp is equipped with perforated gaskets, which can increase the load when the optical cable is dropped.
Contacta ahora
The performance advantages of ADSS suspension clamp set: (1).The stress of the pre-twisted suspension clamp is distributed in a larger area, which greatly reduces the influence of static stress on the optical cable, greatly improves the ability of the optical cable to withstand stress, and the ADSS suspension clamp has the same effect as the ADSS optical cable. Larger contact area, uniform stress distribution, no stress concentration points, and at the same time enhances the rigidity of the optical cable at the hanging point, which provides better protection.
Contacta ahora
ADSS suspension clamp material features: 1.Rubber clamp: It is composed of high-quality rubber and aluminum composite plate reinforcement, with chemical resistance, ozone resistance, weather resistance, aging resistance, high and low temperature performance, high strength and elasticity, and can withstand less pressure.
Contacta ahora
Retention Clamp for ADSS cable single extension 50M span cable diameter 9.0-9.5mmTension splint for ADSS tower is made of forged hot dip galvanized steel.use: for installation and maintenance of aerial construction fiber optic networks.Technical Characteristics1. Fitting material: Steel under ASTM A-362. Minimum yield strength: 250Mpa.3. Minimum tensile strength: 400Mpa4. Post fastening method: By 3/4” steel tape.5. Solder points with smooth and uniform finishes6. Hot dip galvanized according to ASTM A 123 Dimensions1. Fitting base dimensions:
Contacta ahora
J-type clamp is a commonly used FTTH accessory, which is widely used in optical fiber communication projects. The material is galvanized iron, hot-dip galvanized anti-oxidation surface treatment. Convenient to use, securely fixed, strong and durable.Features: Dimension: 178×90×50mmUnit weight: 518g Carton size: 400×300×300mmQuantity per carton : 50 pieces Material: carbon steel body and rubber inserted Cable diameter: 10-15mmDimension image:
Contacta ahora
The pole clamp is suitable for connecting the tension suspension clamp and the electric pole. Features: 1. Product manufacturing is strictly controlled and meets production standards. 2.The surface of the product has no burrs and is relatively smooth. 3. Support customization of a variety of special-shaped productsThe hoop device is composed of a hoop plate, a wing plate, a tie rib plate, a bolt and an inner liner. An embedded hoop, which is formed by joining the left and right halves of the hoop.
Contacta ahora
Outer wire length: 1100, 1200, 1300mm Applicable range: within 120m Large fiber optic cable outer diameter: 16mm Grip strength of wire clamp: 10-30KNTensile strength: 50KN Scope of application: ADSS optical cable Components: guy grip wire, thimble clevis, U-shaped hanging ring, extension ring, nut, bolt, closed pin, etc. Features: light, simple structure, easy to install. Conditions of use: Used for fiber optic cable projects with a span of less than 150m, a line turning angle (elevation angle)> 15o, and a cable ultimate tensile strength (UTS) less than 15
Contacta ahora
Fiber to the home FTTH accessories, S-type fixing cable clamp are composed of stainless steel wire and flame-retardant ABS plastic parts. It is used to bind the self-supporting drop-in optical cable suspension wire and hang the optical cable on the supporting device.The S type cable clamp is used to bind the self-supporting leather cable suspension wire and hang the optical cable on the supporting device, be steadily strengthened and tightened. There are several colors can be chosen: gray, black, white.Instruction: Wrap the 2-5mm optical brazing wire in the cylindrical groove of
Contacta ahora
The suspension support hook clamp made of hot dip galvanized steel, the dimension is 120mm (L)and 10mm as diameter of the hook. There is one hole of M14 punched on the base plate. The thickness of the base plate is 3.2mm.
Contacta ahora